SmartgridOne Controller installation checklist

Use this checklist with the customer before the site visit. It helps identify account, network, device, and cabling issues before the installer arrives. Complete sections 1 through 6 in advance and use section 7 during commissioning.

1. Account and licence

• The installer has an active installer account in SmartgridX, or the organisation owner has already registered one.
• The controller licence has been purchased and is available.
  • Licences can be purchased in bulk and assigned to a controller serial number after installation.
• The controller serial number and verification code are available so the controller can be claimed in SmartgridX.

2. Site and devices

• The controller model has been confirmed: SmartgridOne Pro (EDS) or SmartgridOne Light (M1S).
  • Wiring and mounting requirements differ by model. Check the specifications and installation instructions.
• The required cabling has been determined for every connected device.
  • See the network requirements and wiring and connectivity guidelines.
• Every inverter, battery, EV charger, heat pump, meter, or other device to be connected appears in the list of supported device integrations.
• A working, supported grid meter is available, such as a P1 meter, A1 meter, or another supported grid measurement.
  • For P1 or A1, plan a direct connection to the digital meter.
• Belgium only: the P1 user port of the digital meter has been activated through Mijn Fluvius.
  • Measurements may take several hours to appear after activation, so activate the port in advance.

3. Network

• A fixed, wired internet connection with an RJ45 socket is available at the controller mounting location.
  • A wired connection is the required and recommended connection for the controller.
• The network cable has been tested with a laptop to confirm that it provides internet access before connecting it to the controller.
• If a 5G router is used, its subscription provides at least 5 GB per month, plus 1 GB for every device above five devices.
  • A data-saving mode is available to reduce usage where necessary.
• CAT5e cable or better is available.
  • Use shielded cable in commercial or industrial environments.
  • Keep each Ethernet run at or below 100 m; use a network switch or repeater for longer distances.
• The controller and all communicating devices are on the same subnet.
  • For example, 192.168.1.10 and 192.168.1.25 are on the same 192.168.1.x subnet. A device on 192.168.200.x cannot normally communicate with a controller on 192.168.1.x.
• The building owner or network administrator has confirmed whether fixed IP addresses are required.
  • DHCP is the default and recommended configuration. Use a fixed IP address only when unavoidable and record the assigned address.
• The outbound firewall rules allow the required connections:
  • TCP 80 and 443 for general internet communication.
  • TCP 1194, or TCP 1192 / 35000-40000, for updates, diagnostics, and remote support.
  • TCP 1883 and 8883 for MQTT when live external control signals are used.
  • UDP 123 for NTP time synchronisation.
• The customer's IT team knows that no inbound ports or port forwarding are required.
  • Port forwarding is unnecessary and creates a security risk.
• If the customer network uses a domain allowlist, *.eniris.be, *.eniris.io, and *.eniris.com have been allowed.
• It has been decided whether the installation will use a dedicated VLAN.
  • A VLAN is optional. All devices that communicate with the controller must use the same VLAN.
• If Ethernet cabling is unavailable, powerline adapters have been considered and the relevant power sockets have been checked for compatibility.
  • Powerline adapters generally need sockets on the same electrical phase.

For the complete and most recent port and domain requirements, see Advanced network settings.

4. RS485 wiring, when applicable

• Shielded twisted-pair cable is used, with one pair for RS485 A and B and a characteristic impedance of 100-120 ohm.
• Devices are wired in a daisy chain.
  • Do not use a star topology and do not connect the same bus to multiple controller ports.
• Every device on the bus has a unique address.
  • Start with low addresses so devices can be discovered more quickly.
• Termination and biasing have been configured for the controller model and bus topology.
  • Use 120 ohm termination at the ends of the daisy chain. Some controller models provide configurable termination through DIP switches; other models require external termination resistors.
• The cable shield is grounded at one end only, using the electrical earth of the installation rather than signal ground.
• Approximately five devices or fewer are planned per RS485 bus for optimal performance.
  • The absolute maximum is 20 supported unit-load devices. Use an RS485 expansion accessory or additional available buses when more capacity is required.

See the RS485 wiring guidelines for model-specific wiring, termination, and biasing instructions.

5. Power and mounting

• The mounting location has been selected for wall or DIN-rail mounting, depending on the controller model, and is accessible for power and network cabling.
• A power socket is within reach of the mounting location.
  • Eniris supplies the AC wall adapter as standard; the customer only needs to provide a suitable socket.
• The accessories included in the order have been checked.
  • A P1-to-USB cable, DIN-rail kit, and RS485-to-USB adapter are not always included as standard.
• The power circuit and socket are externally protected by a miniature circuit breaker (MCB) and residual-current circuit breaker (RCCB) in accordance with local regulations.
• The mounting location meets the environmental requirements.
  • Do not install the controller outdoors, in direct sunlight, near flammable or explosive materials, gas pipes, radiators, or unventilated lead-acid batteries.
  • Do not install it in a damp, flood-prone, or vibration-prone location.
• The controller will not be mounted on its side and at least 1 cm of clearance is available around it.
• The controller enclosure will not be intentionally connected to electrical earth.
  • This does not affect the separate RS485 cable-shield grounding requirement in section 4.
• Strain relief is provided wherever cables may be exposed to mechanical stress.

Review the safety, maintenance, and legal notices before installation.

6. Prepare the controller

• Power the controller and leave it connected for at least 10 minutes so it can download the latest software updates.
• Claim the controller in SmartgridX.
• Complete the initial configuration wizard and enter the essential installation information.
• The installer knows how to contact Eniris Support.
  • Create a ticket first at eniris.com/support.
  • Telephone support is available at +32 9 377 12 58 after a ticket has been created.

7. Installation day and commissioning

• Connect and configure the devices through the commissioning wizard.
• A stable internet connection is available throughout commissioning.
  • The connection is required for automatic firmware updates and allows Eniris Support to assist remotely when necessary.
• The end user's email address is available so they can be added as a user in SmartgridX after installation.